Adam.birds: Created page with "== Setup Bacula Client on Linux using IPv6 == === Login to client server and sudo up. === ====CentOS==== Check NICs. Configure Interface: This is what needs setting in '''/..."

2016-04-28T10:12:50Z

Created page with "== Setup Bacula Client on Linux using IPv6 == === Login to client server and sudo up. === ====CentOS==== Check NICs. Configure Interface: This is what needs setting in '''/..."

New page

== Setup Bacula Client on Linux using IPv6 ==
=== Login to client server and sudo up. ===
====CentOS====
Check NICs.

Configure Interface:

This is what needs setting in '''/etc/sysconfig/network-scripts/ifcnfg-eth1'''

<pre>
ONBOOT=yes
IPV6INIT=yes
IPV6_AUTOCONF=yes
</pre>

'''Then'''

<pre>
#Check eth1 has a IPv6 'bac' address.
ip a

#If not run
ifup eth1

#After a minute retry
ip a
</pre>

<pre>
ip a

3: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP qlen 1000
link/ether 90:b1:1c:23:ff:39 brd ff:ff:ff:ff:ff:ff
inet6 2a02:22d0:bac:0:92b1:1cff:fe23:ff39/64 scope global dynamic
valid_lft 604741sec preferred_lft 43141sec
inet6 fe80::92b1:1cff:fe23:ff39/64 scope link
valid_lft forever preferred_lft forever

</pre>

====Ubuntu/Debian====

This is what needs setting in '''/etc/network/interfaces'''

<pre># Backup Network
auto eth1
iface eth1 inet6 auto</pre>

=== Install Bacula client. Skip if already installed.===

<pre>
yum install bacula-client
</pre>

=== Edit bacula-fd.conf ===

/etc/bacula/bacula-fd.conf

<pre>
FileDaemon {
Name = [insert hostname here]
FD Addresses = {
#ipv4 = { addr = 0.0.0.0; port = 9102; }
ipv6 = { addr = ::; port = 9102; }
}
WorkingDirectory = /var/spool/bacula
Pid Directory = /var/run
Maximum Concurrent Jobs = 20
Heartbeat Interval = 10
}

Director {
Name = Ziff-dir
Password = "[insert bacula password here]"
}

Director {
Name = Ziff-tray
Password = "[insert bacula password here]"
Monitor = yes
}

Messages {
Name = Standard
director = Ziff-dir = all, !skipped, !restored
}
</pre>

=== Final Client checks ===

<pre>
#Restart bacula-fd
service bacula-fd restart

#Set bacula-fd to start on boot
chkconfig bacula-fd on

#Check listening port reports IPv6
lsof -i :9102

COMMAND PID USER FD TYPE DEVICE SIZE/OFF NODE NAME
bacula-fd 5893 root 3u IPv6 17820696 0t0 TCP *:bacula-fd (LISTEN)

</pre>

=== Backup Server ===

Run the following on the backup server.

<pre>

#Open bacula console
bconsole

#Reload the configurations
reload

#Status client and select client
status client

#Bconsole will report back the IPv6 address.

Connecting to Client srv-78_109_168_211 at 2a02:22d0:bac:0:92b1:1cff:fe23:ff39:9102

</pre>

[[Category:Bacula]]
[[Category:Backups]]
[[Category:Linux]]
[[Category:Contents]]

Bacula Linux IPv6 Setup - Revision history

Adam.birds: Created page with "== Setup Bacula Client on Linux using IPv6 == === Login to client server and sudo up. === ====CentOS==== Check NICs. Configure Interface: This is what needs setting in '''/..."